Super Micro Computer, Inc. | Support

MySupermicro

Support Home

Downloads

Online Support FAQ Search OS Compatibility

Welcome to the FAQs section. You may search by keyword or browse by Category/Keyword using the side menus. For your convenience, below are the 10 most-requested FAQs.

If you have a technical support question please visit the Technical Support Contact page for details. Thank you.

Top 10 Most-Requested FAQs

	Question	Date
1	Which key is to be pressed to enter Bios when the machine is connected via serial console (Board X9SCL-F)? We already tried "DEL", "F4", "F11"... but no go.	04/13/12
2	I have a supermicro server, that stops at boot, with the msg SYSTEM INITIALIZING with BA code at the right.	07/05/13
3	When I enable secure boot in X10DRC-LN4+, it shows message "WARNING: CSM is Loaded! Disable the CSM in Setup. Repeat operation after Reboot to ensure UEFI Video (GOP) driver is operational.".	07/17/15
4	How do I enable Turbo mode to get the maximum Turbo mode speed on my X10DRi motherboard?	09/11/15
5	I plug in 4GB of memory into my P8SAA board but Windows XP only shows 3GB of memory. Everything works fine but why does Windows shows only 3GB of memory?	01/15/05
6	I noticed X8 DP series motherboard showing "ERST: Failed to get Error Log Address Range" message during the RHEL/CentOS 6.2,6.3 version while booting. What is this problem related to?	02/08/13
7	I have a storage Chassis SC846BA-R1K28 and Mainboard X9DR7-LN4F did not start up anymore. Then I unplugged and replugged some SAS cables, and tried to locate which Disk slots are served by which cable. After pushing the power button it showed "supermicro"-screen with "System Initializing..." on the bottom and then did not do anything further. IPMI shows the message "System initializing... B7". Removing the Bios battery for some time did not solve the problem. I did not find an answer on the internet yet - could you please tell us what this means and how I can recover from this?	10/04/13
8	How do I create a bootable USB stick?	10/11/13
9	I am using 4x K20 in 7047GR-TPRF (X9DRG-QF) but gets the error: !!!!PCI Resource ERROR!!!! PCI OUT OF RESOURCES CONDITION: Error: Insufficient PCI Resources Detected!!! System is running with Insufficient PCI Resources! In order to display this message some PCI devices were set to disabled state! It is strongly recommended to Power Off the system and remove some PCI/PCI Express cards from the system! To continue booting, proceed to Menu Option and select Boot Device or . WARNING: If you choose to continue booting some Operating Systems might not be able to complete boot correctly!	02/01/13
10	There is an issue. When we are generating the component rating of the system it shows UNRATED for all the components (Please see the attachment for better idea), while a normal system shows their components rating by using same methods. Super Micro Workstation Configuration Details as below:- Motherboard Supermicro X9DAI Processor Xeon E5 2665 2.40 Ghz (Single CPU) RAM 16 GB REG. DDR3 1600 Mhz. HD 2TB Sata Graphic Card Nvidia Quadro 600 OS Windows 7 -64 bit – Prof. Please kindly provide the solution for the same ASAP.	03/21/14

Terms & Conditions \| Privacy \| Investor Relations \| Jobs \| Site Map
SuperServer® \| Motherboard \| Chassis \| Rack Cabinet \| SuperBlade® \| Embedded \| Networking \| Storage \| Accessories \| AMD Solution \| Power Supplies
	Copyright © 2024 Super Micro Computer, Inc.
Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.